Preamp gain stage

One preamp stage, a triode or a small pentode, with the parts amp designers use to shape it. Switch in a small or partial cathode bypass, caps at the grid and plate, a treble peaker, a bright cap on a volume, or a cathode follower after the stage. Change any value and see the frequency response, the distortion, and where the distortion starts.

Sine at

Swipe sideways for the whole drawing. Tap a part to jump to its value. The red numbers are DC voltages to ground.

Frequency response

The graph shows the gain from the source to the point you picked, for a small signal, with every part and the tube’s capacitances counted. The gray curve is the stage with the tone parts switched off (the cathode bypass and the load stay in). A sweep draws the curve at standard values around yours, lightest for the lowest.

Output, two cycles

outputinput times the small-signal gain at this frequency

Harmonics

evenodd dB below the fundamental, 2nd to 10th

All values

Other parts

What the parts do

A triode stage’s gain is set by its plate load and by how much of the signal on its cathode resistor is bypassed to ground. Every other part on this page changes that gain at some frequencies more than at others.

A cap to ground cuts treble only together with the resistance that feeds it. A bigger resistance or a bigger cap starts the cut at a lower frequency. For the cap from grid to ground and the plate-to-grid cap, that resistance is the source and the grid stopper. For the plate cap, it is the plate resistor and the tube’s plate resistance. For the capacitance at the next grid, it is whatever feeds that grid. A resistor in series with any of these caps stops the cut part way, so the treble drops by a fixed amount (a shelf) and then levels off. A cap across a resistor in the signal path does the opposite. The treble peaker and the bright cap let treble go around the resistor.

The Miller effect. A tube has a small capacitance from its plate to its grid, about 1.7 pF in a 12AX7. When the grid moves up 1 V, the plate moves down by the stage’s gain, 60 V in a stage with a gain of 60. The voltage across that small capacitance changes by 61 V, not 1 V, so 61 times as much current flows through it. To the source it acts like a cap to ground 61 times larger, about 100 pF. That cap cuts treble together with whatever resistance feeds the grid. A plate-to-grid cap added on purpose is multiplied the same way.

The bass is set by the coupling cap together with the load after it, and by the cathode bypass cap. For the coupling cap by itself, with the stage as its source, try the corner calculator. A small bypass cap brings back the full gain only at higher frequencies, where the cap’s impedance is lower than the cathode resistor. A resistor in series with the bypass cap limits how much gain comes back.

Pentodes In a pentode, the screen grid’s voltage sets how much current the tube can pass, and the plate voltage hardly matters. With the screen held steady by its bypass cap, the stage’s gain is several times a triode’s. The screen bypass cap shapes the response the way the cathode bypass does. Below a frequency set by the cap’s size, the screen voltage moves with the signal, opposite to the grid, and the gain falls. Wired as a triode, the screen connects to the plate, and the stage acts like a triode with a mu of about 20 to 40.

Grid resistor The source on this page has no resistance, so the grid doesn’t need a resistor to ground. Switched in, the grid resistor forms a voltage divider with the source resistance and the stopper. 1 MΩ after 68 kΩ lowers the level by about half a dB.

Feedback to the grid A resistor from the output back to the grid sends back an inverted copy of the signal, which cancels part of what comes in. How much it cancels depends on the resistance in front of the grid, on this page the source and the stopper. The stage’s gain comes down toward the feedback resistor divided by that resistance, and distortion falls along with the gain. With 1 MΩ and 68 kΩ, a 12AX7 stage’s gain drops from about 60 to about 12. With the feedback connected at the plate, a cap in series keeps the plate’s DC off the grid. At low frequencies, where that cap’s impedance is higher than the feedback resistor, the feedback fades. With the feedback connected after the coupling cap, no extra cap is needed, and the coupling cap is inside the feedback loop.

Warnings Red text flags grid current in the stage or in the follower, the tube nearly cut off at rest, or the solver not settling.