Reactive load
A load that acts like a speaker, built from resistors, inductors and a capacitor. Set the bass peak you want, then see the impedance and phase from 20 Hz to 20 kHz, how hard each part works at your amp’s power, and your own measured cab curves on the same graph.
Swipe sideways for the whole drawing. Tap a part to jump to its value.
A measured curve can be a DATS .zma file, or any text file with one point per line: frequency, ohms, and phase in degrees if you have it. It stays in your browser. Nothing is uploaded. Download an example file.
Driven by an amp
This graph compares the voltage across this load with the voltage across a plain resistor of the nominal value, driven by the same amp. The higher the amp’s output impedance, the more the voltage rises where the load’s impedance rises, at the bass peak and in the treble.
How hard each part works
The table shows the most each part has to handle when the amp plays a steady sine at its full rated power, anywhere from 20 Hz to 20 kHz. The figures are rms, and each is listed with the frequency where it happens. Buy parts rated for the bold figure: watts for a resistor, current for an inductor, voltage for a capacitor (peak voltage is 1.41 times rms). Music runs far lower on average, but a note held on the bass peak gets close. Leave margin for heat and for an amp pushed over its rating. At low damping factors the figures run high. They assume the amp’s voltage keeps rising as the load’s impedance rises, and a real tube amp runs out of plate swing first.
All values
Other parts
How the load acts like a speaker
A speaker’s impedance has three parts. At the bottom is the voice coil’s resistance. In the bass there’s a peak where the cone resonates. Up top, the coil’s inductance takes over and the impedance climbs.
R1 is the coil’s resistance. R3, L3 and C3, wired side by side, make the bass peak. At the resonant frequency L3 and C3 cancel each other and only R3 is left, so the peak is about R1 plus R3. Below that frequency the current goes around R3 through L3, and above it through C3, so the impedance falls away on both sides. L1 makes the treble climb.
In a real speaker the treble climb gets less steep higher up, because the iron around the coil soaks up more of the energy. L2 with R2 across it copies that. L2’s impedance rises with frequency until it equals R2. Above that the current goes through R2, and only L1 keeps climbing. A measured speaker’s impedance also starts rising slowly from a few hundred hertz. L4 with R4 across it adds that slow early rise. Without it, a fit to a measured curve sets R1 higher than the coil’s real resistance.
Damping factor
Damping factor is the speaker’s nominal impedance divided by the amp’s output impedance. An amp with 4 Ω of output impedance on an 8 Ω speaker has a damping factor of 2.
The amp’s output impedance is in series with the speaker, so the two share the amp’s voltage. With a low output impedance (a high damping factor), nearly all the voltage reaches the speaker at every frequency. With a high output impedance, the speaker’s share is bigger wherever its own impedance is high, at the bass peak and in the treble. The graph under “Driven by an amp” shows it.
The name comes from the cone. A moving voice coil works as a small generator, most of all at resonance. When the amp’s output impedance is low, current from that generator flows back through the coil and brakes the cone. The coil’s resistance is always in that path. Once the amp’s output impedance is well under the coil’s resistance, going lower changes little. Damping factors of 20 and 200 sound about the same.
Rough damping factors for each kind of amp follow. Solid-state amps run from 20 to several hundred at the jack. Tube hi-fi amps with lots of feedback run about 5 to 20. Tube guitar amps with the usual feedback from the speaker, like blackface Fenders and Marshalls, are well under 1 (about 0.3 to 0.7 in the power amp tool). Tube guitar amps with no feedback, like a tweed Deluxe or an AC30, are under 0.1, because pentodes and beam tubes have a high plate resistance. Feedback from the speaker lowers the output impedance.
Each button sets a damping factor for one kind of amp. The figures come from the power amp tool with typical part values. Real amps vary with the feedback resistor, the transformer tap it connects to and the tubes. The slider covers tube amps. For solid state, type a bigger number. For one particular power section, see the power amp tool.
Warnings The summary above the graph turns red if the load can’t be solved.