Preamp tube load lines

One preamp gain stage, a triode or a small pentode, drawn on its tube’s plate curves. Set the supply, the resistors and the bias, and see where the tube sits and how far it can swing each way before the grid draws current or the tube cuts off. Then drive it with a sine and watch it move along the load line.

A high-mu twin triode (mu about 100) that runs at low plate current. It’s the usual preamp tube in guitar amps.

Sine at

Swipe sideways for the whole drawing. Tap a part to jump to its value. The red numbers are DC voltages to ground.

Plate curves

Output at the load, one cycle

outputinput times the small-signal gain

Harmonics

evenodd dB below the fundamental, 2nd to 10th

All values

Reading the chart

Plate voltage runs along the bottom and plate current up the side.

Grid curves

Each gray curve is the plate current at one grid voltage as the plate voltage changes. The dark curve is the grid at 0 V.

DC load line

With this plate resistor, the plate’s voltage and current can only be at a point on this red line. One end is the full supply voltage at zero current. The other end is the current that would flow if the tube were a dead short.

Cathode bias line

With cathode bias, the plate current through the cathode resistor makes the bias voltage, so more current means more bias. The dotted line shows every point where the current and the bias agree. The tube idles where this line crosses the DC load line.

Operating point

The two lines cross at Q. The stage idles there.

AC load line

The signal passes through the coupling cap, so for the signal the next stage’s load is in parallel with the plate resistor. The signal moves along this steeper dashed line through the idle point, Q. A cathode resistor with no bypass cap adds to the line’s resistance.

The signal

The blue path is where the stage goes during one cycle of the sine, with every part in the circuit counted. The two open circles mark how far the stage can swing each way and stay clean.

Dissipation rating

In the shaded corner, past the dashed curve, the plate is over its dissipation rating.

Headroom and uneven clipping

The stage runs clean between two limits. As the grid swings up, the plate voltage falls. The clean swing ends where the grid reaches the cathode’s voltage and starts pulling current. As the grid swings down, the plate voltage rises. The clean swing ends where the tube cuts off. The closer of the two limits sets the clean headroom.

A triode stage seldom clips both halves at once. The closer limit flattens its side of the wave first, so the wave turns lopsided and even harmonics appear (orange on the harmonics graph). The bias point sets which side that is.

Where the curves are bunched together or spread apart along the AC load line, the stage distorts before it reaches either limit.

Warnings

Red flags the plate over its dissipation rating, grid current moving the bias, the tube nearly cut off at rest, or the solver not settling.

Pentodes

A pentode’s plate current depends far more on its screen voltage than on its plate voltage. Its curves run almost flat, and the stage’s gain is several times a triode’s. The curves are drawn for the screen voltage this stage idles at. The screen resistor sets that voltage, so changing the resistor moves the curves. When the stage is driven hard, the screen pulls more current, its voltage sags and the curves move down. That is part of why a pentode stage compresses. Wired as a triode, the curves show the plate and screen current added together.

The 12AX7

A high-mu twin triode (mu about 100) that runs at low plate current. It’s the usual preamp tube in guitar amps.

Model. 12AX7 / ECC83 / 7025: a Koren-equation model, fitted to eight vintage-era plate charts together (Brimar, GE, RCA, Tung-Sol, Sylvania, Philips, Telefunken and JJ’s ECC83S, which agrees with them). The match counts most below 2.5 mA and 350 V, the range a guitar preamp uses. The published points 250 V on the plate with −2 V on the grid (1.2 mA) and 100 V with −1 V (0.5 mA) count too. The model is within about 2.5 to 4 V rms of each chart, and the charts differ from each other by 5 to 10 V. In the model the grid acts as if it were 0.75 V more positive than it is (a contact offset). That puts the model’s 0 V curve on the charts below 1 mA. At 100 V with −1 V on the grid, each volt on the grid moves the plate current 1.12 mA and the plate resistance is 89 k, as the charts read (the sheets print 1.25 mA/V and 80 k). It stands for the type, not any one tube. Real tubes spread 20 % and more.

Dissipation. 1 W per section.

Starting stage. 300 V supply, 100 kΩ plate resistor, 1.5 kΩ cathode resistor bypassed by 22 µF, 22 nF into 0 Ω, a 68 kΩ grid stopper, and 1 V peak at 1 kHz. It’s a common setup for the type, not a copy of any one amp.