Power load lines

A power tube output stage drawn on the tube’s plate curves. Pick single-ended or push-pull, set up the screen supply, bias, driver and output transformer, and load it with a resistor or a speaker. Then drive it with a sine and read the power, the distortion and how hot each tube runs.

Put it in a power amp

A beam power tube, the usual output tube of the larger Fender amps and many others, in pairs or fours.

Swipe sideways for the whole drawing. Tap a part to jump to its value. The red numbers are DC voltages to ground at idle.

Plate curves

At the speaker, one cycle

outputthe fundamental alone

Currents

Harmonics at the speaker

evenodd dB below the fundamental, 2nd to 10th

All values

Reading the chart

One tube Each gray curve shows the plate current at one grid voltage, across the range of plate voltage. Connected as a pentode or tetrode, the tube’s screen voltage stays fixed. Connected ultra-linear or as a triode, the screen voltage moves with the plate. A single-ended stage idles at the red dot. With a signal it moves up and down the load line. The slope of that line is the speaker load as the tube sees it through the transformer, plus the primary’s resistance. The steep red line is the DC load line. Its slope is the primary’s resistance (plus the supply resistance, if the supply sags). In push-pull, each tube follows the class A line, half the plate-to-plate load, while both tubes conduct. Once the other tube cuts off, it follows the steeper class B line, a quarter of the load. For the rest of the cycle its current is zero.

Both tubes In a push-pull amp, the two grids are driven opposite ways. When tube A’s grid goes up a volt, tube B’s goes down a volt, and the two plates swing opposite ways too. The composite curves show tube A’s current minus tube B’s at every point of that swing, for a perfect center tap. Together the two tubes follow one straight load line. It crosses zero current at the idle plate voltage, and its slope is a quarter of the plate-to-plate load. Where the curves along that line are bunched together or spread apart, the stage distorts. A kink near the middle at cold bias is crossover distortion.

Speaker loads A speaker’s current and voltage don’t peak at the same moment, so the path on the chart opens from a line into a loop. Near the speaker’s resonance the load is several times the rated impedance, and the loop is long and flat. In the treble the voice coil’s inductance tilts the loop the other way. With a speaker load, the distortion figures and Find full power are measured on the speaker’s current, because current is what pushes the cone. Distortion measured on the voltage reads higher, because the speaker’s impedance is higher at the harmonics than at the note. Both are shown. For your own speaker, pick Measured curve from a file in the Load menu. It opens a DATS .zma file, or a text file with frequency, ohms and phase on each line (example file).

Warnings and notes Red marks anything that wears a tube out fast or makes the numbers doubtful. That covers plate or screen dissipation over the rating (at idle or averaged with the signal), grid current shifting the bias, and the solver not settling. A dotted underline with a plain note marks anything over the datasheet rating that is still common in guitar amps: plate or screen voltage over the rating, and more grid-to-cathode resistance than the sheet allows. The ratings come from each tube’s datasheet. Later sheets list higher ratings for several types, and you can type those in.

Feedback Negative feedback sends part of the speaker voltage back to the driver. Most guitar amps do it with a resistor from the speaker jack to the phase inverter. The driver on this page is ideal, so the page shows what feedback does to the output stage by itself. Distortion drops. The output voltage stays steadier where the speaker’s impedance rises. At cold bias, the distortion that remains is concentrated around the crossover point. A real inverter clips and runs out of bandwidth, so feedback does less in a real amp.

Full power With Clipping picked, Find full power turns the signal up until the stage runs out of room, and shows the power just short of that point. The stage can run out of room in three ways, and the first one reached sets full power. One, the grids reach 0 V and start pulling current. A DC-coupled driver can push the grids over 0 V, and then the limit is where grid current loads the driver down. Two, the plates swing down into the knee of the curves. We put that point where the tube’s plate resistance has dropped to equal the load, which leaves the grid with half its usual control over the current. Three, a single-ended tube nears cutoff on the low-current half of the swing. We put that point where the tube’s gain has dropped by half. Pick a THD figure instead, and the signal goes up until the distortion reaches that figure. With no feedback, the EL34, KT88 and KT66 run at 5 to 7 % THD over a wide range of levels and reach 5 % long before they clip. That is one reason amps are rated with feedback on. The search takes a few seconds, and the signal is left at the level found.

Supply sag A real B+ drops as the stage pulls more current, so the page starts with a supply that sags. It is a power transformer sized for the tubes, with the bias voltage coming from a tap on its high-voltage winding, as in a blackface Fender. The supply is modeled as a fixed voltage behind the supply resistance, with the reservoir cap at B+. The fixed voltage is set so that the idle B+, the bias and the idle figures stay where you put them. Only the signal moves B+. A class AB push-pull stage pulls more current the harder it’s driven. B+ drops, the screens drop further, and full power comes down. A class A stage pulls about the same current at any level, so B+ barely moves, though the signal current still runs through the reservoir cap. Only the average B+ is modeled, not the 100 or 120 Hz ripple. The supply resistance stands for the windings and the rectifier together. To measure it on a real amp, compare B+ at idle with B+ at full power into a load.

Core saturation The iron core of the output transformer can hold only so much magnetic flux. Flux builds up over each half cycle of the voltage on the primary, so a lower note or a bigger voltage swing builds up more. The level where the iron is nearly full is called the knee. Over the knee, the primary’s inductance collapses. The primary pulls a burst of current on each peak, the load on the plates drops sharply, and a low note at full power thins out and distorts. A steady DC current in the primary starts the core part of the way up, closer to the knee on one side. That happens in a single-ended stage, and in a push-pull pair that isn’t matched. The knee is worked out from the primary’s turns, the core’s area and the steel’s knee flux density, the figures a transformer winder uses. The starting values are placeholders, not a real transformer. The readouts show the peak flux compared with the knee, and the lowest note that stays under the knee at this swing. Hysteresis and core losses are left out. Below the knee, the inductance stays at the primary inductance you set.

The 6L6GC

A beam power tube, the usual output tube of the larger Fender amps and many others, in pairs or fours.

Curves. The beam law from the bench, fitted to the Tung-Sol sheet (1960): plate curves with 250 and 400 V on the screen, its three screen-current charts and its two grid-current charts. GE’s 400 V and RCA’s 300 V plate curves (1959) are fitted with them.

Expected error. The plate current is within about 3 to 4 mA rms of Tung-Sol’s curves, 5 mA of GE’s and 4.5 mA of RCA’s (7 mA near the knee, where a curve bends over). The screen current is within about 2 to 3 mA. The grid current is within about 3 mA with 400 V on the screen. With 250 V on the screen it reads up to 11 mA low, and it also reads low where the plate swings under about 100 V. The Tung-Sol class A1 table reads 6 to 9 % above the curves on the same sheet, and the model follows the curves. JJ’s current sheet reads about 4 % below the model. Real tubes of one type vary by 20 % or more, so the tube in your amp can be further off than this. The sheet’s curves cover screen voltages from 50 to 400 V. Outside that range the figures are extrapolated, and you get a note about it.

Ratings used. Plate 500 V, screen 450 V, plate dissipation 30 W, screen dissipation 5 W, grid circuit 100 kΩ with fixed bias, 500 kΩ with cathode bias (Tung-Sol, design maximum). You can change the voltage and dissipation ratings under Bias and ratings, for a later sheet or a different make.

Starting stages. The push-pull stage starts at 450 V B+ into 4 kΩ plate to plate, with fixed bias and the idle at 70 % of the plate rating. The single-ended stage starts at 350 V into 4.2 kΩ, with cathode bias and the idle at 90 %. Both stages use 470 Ω screen stoppers, 100 nF coupling caps and 1.5 kΩ grid stoppers, as in many Fender amps. These are common setups for the type at typical guitar-amp voltages, not copies of any one amp. Where they run over the sheet’s voltage or grid-circuit ratings, as guitar amps often do, you get a note about it.