Ibanez TS808 Tube Screamer tone stack
Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.
The tone stage after the clipping. It’s a fixed low-pass, then an op-amp stage where the Tone pot boosts or cuts the treble.
Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.
At this setting
0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.
Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.
Listen
You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.
Source and load
Driven by
Driving
The knobs
- Tone
- An active control. First comes a fixed 1 kΩ and 220 nF low-pass at 720 Hz. Then the pot moves a 220 Ω and 220 nF branch between the op-amp’s input and its feedback, which cuts or lifts the treble above about 1 kHz.
Parts
- R7
- 1 kΩ, With C5, a low-pass filter at about 720 Hz ahead of the tone stage.
- C5
- 220 nF, The low-pass cap. Together with the clipper’s high-pass, it makes the mid hump.
- R9
- 10 kΩ, Biases the tone stage’s plus input.
- Tone
- 20 kΩ, Slides the R8/C6 network from the plus input, where it cuts treble, to the minus input, where it boosts it.
- R8
- 220 Ω, Tone network resistor.
- C6
- 220 nF, Tone network cap.
- U2
- Tone stage.
- R10
- 1 kΩ, Tone stage feedback resistor.
Source and load
Driven by: op-amp buffer. Driving: volume pot, 100 kΩ. Load: 1 kΩ into the 100 kΩ Level pot at full, then the output buffer’s 510 kΩ bias resistor.
Sources
- matsumin, drawing of the Maxon OD-F1’s changes against the Tube Screamer, 2007 (the OD-F1 build)
Values and wiring are the same as in the op-amp overdrive circuit on the bench, so the two always match.
How a tone stack works
Two ways through In the FMV stack the treble cap is small, so it passes only the highs, straight to the top of the treble pot. Everything else goes through the slope resistor, then the bass and mid caps. The bass cap feeds the bottom of the treble pot, and the bass pot sits between there and the top of the mid pot. Turned down, it shorts the bass cap’s end toward the mid pot, and the lows drop away. The mid pot sits between the mid cap and ground, so turning it up lifts the whole lower path off ground. The output is the treble pot’s wiper, a mix of the highs at the top of its track and the lows and mids at the bottom.
The mid scoop Where a stack passes the bass and the treble by different paths, there’s a stretch in between where neither path passes much. That dip in the mids is the scoop. Its depth and center move with the knobs. In the FMV stack the slope resistor and treble cap set where it sits, and the mid knob fills it in. A plain low-pass or high-pass filter has no scoop.
Warnings The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.